This is the receiver for KYOSHO MR-03EVO and MA-030EVO
it can be used for sanwa transmitter
M17,M12S,M12,MT44,MT4S,MT4,M11X etc.
MX EVO RX-SANWA V2 . 15 Manual
The MX EVO RX -SANWA is a SANWA FH3/FH4 compatible ultra - miniature receiver for KYOSHO's MR -03EVO and MA -030EVO , with an output speed of up to 2 . 6ms in EVO mode . It can work not only in EVO mode , but also in 4CH PWM standard signal mode .
Features:
Size: 10.5*10.0*3.5mm;
Weight: 0.72g;
Working voltage: 3.0V or 3.3V;
Compatible with SANWA FH3/FH4 protocol;
Support EVO and 4CH PWM two working modes;
The output speed in EVO mode is 2.6ms;
The output speed in 4CH PWM mode is 5 .4ms;
Bind Operation:
Install the MX EVO RX first , then power on the receiver and press the BIND switch until the red LED on the RX changes from slow flashing to fast flashing , and then perform BIND according to the BIND operation requirements of the transmitter (select FH3 or FH4 mode) , When the red LED on the RX changes from fast flashing to steady on , it means that BIND is successful and has received the signal (if the SANWA transmitter does not exit and the BIND mode LED changes from steady on to slow flashing) .
Red LED status indication:
The red LED on the MX EVO RX is an indication of the working status of the RX:
1) When the red LED flashes slowly , it means that RX is waiting to receive a signal;
2) When the red LED flashes quickly , it means RX is in BIND mode;
3) When the red LED is always on , it means that the RX has received the signal stably .
How to set up the transmitter (when MX EVO RX is used on MR -03EVO/MA -03EVO):
Because the brushless ESCs and servos on MR -03EVO/MA -03EVO cannot set the midpoint and end point , the user can only set the transmitter to adapt to the parameters of MR -03EVO/MA -03EVO . The settings are as follows:
1) TH TYPE = F5 : B5
2) EAP: ST > L150% R150%
TH >H150% B150%
3) D/R: ST >100%
TH >100%
4) REV: ST > REV
TH >REV
Note: Points 2 and 3 can be adjusted according to user habits , and point 4 can be set according to the actual situation .
How the MX EVO RX works in EVO mode:
When users install MX EVO RX on KYOSHO's MR -03EVO/MA -030EVO frame or other products that support EVO mode , MX EVO RX will work in EVO mode .
In EVO mode , when the MX EVO RX is just powered on , the LED on the RX will not flash quickly to indicate .
Note: When using the MX EVO RX on the MR -03EVO and MA -03EVO , be sure to install it in place , otherwise you may burn it; if necessary , place the receiver compartment cover on the MR -03EVO and MA -03EVO Add a small piece of sponge to hold down the MX EVO RX .
How the MX EVO RX works in 4CH PWM mode:
When users install MX EVO RX on EVO - BA1 or other products that support 4CH PWM mode , MX EVO RX will work in 4CH PWM mode .
In 4CH PWM mode , when the MX EVO RX is just powered on , the LED on the RX will flash several times quickly before entering the working mode .
The picture below shows the EVO - BA1 on the left and the EVO - BA1 with the MX EVO RX installed on the right:
How to read RX firmware version:
This function requires GUI support on the PC side , and the receiver and GUI need to be connected through the MX USB - PG - ISP . The remote control must be turned off before the receiver is connected to the GUI , otherwise the receiver cannot be connected to the GUI.
Note:
1) The SW switch on the MX USB - PG - ISP must be moved to the "I" position;
2) When the GUI is connected to the MX EVO RX , the transmitter must be turned off , otherwise the GUI cannot correctly read the information of the MX EVO RX .
3) When the MX USB - PG - ISP is connected to KYOSHO's MINI -Z product , the cable needs to be replaced;
4) MX EVO RX -SANWA V2 . 15 does not support online firmware upgrade function .
GUI download link: update.crossover-rx.com/mxo.zip
Please contact us if you have any feedback or suggestions, thank you!
